A specification is a document a converter can quote from
Most wiper specifications are a size, a GSM and a vague adjective. They arrive at a converter as a price request, come back as a quotation nobody can compare, and end up resolved by whoever answers the phone fastest. The ten fields below are what turn that exchange into something repeatable.
1. The substrate and the soil
Name the material being cleaned, its finish, and the soil: coolant, wax, ink, flux, protein, particulate. “Stainless steel” is not enough — a brushed finish traps soil differently from a polished one, and the wipe that finishes one can scratch the other.
2. The solvent or cleaning chemistry
Water, 70/30 IPA, acetone, a quat disinfectant, a pH 12 caustic. The chemistry decides the fiber and the edge more often than the cleanroom class does. It also decides the packaging: a solvent that attacks the bag is a shelf-life problem, not a cloth problem.
3. The cleanroom class at the point of use
ISO 3–8, or “industrial” if no class applies. Class sets the particle and NVR expectation, the edge type and the documentation level. The ISO class guide maps the classes to typical wiper constructions.
4. The edge
Cut, laser, ultrasonic or heat-sealed. Cut is the economical default; sealed is the default where fiber release matters. State it explicitly — “sealed” alone is ambiguous, because four sealing processes produce four different borders. See cut versus sealed edges.
5. Material and construction
Wood pulp/PP, cellulose/polyester, polyester knit, microfiber, rayon blend, meltblown PP. Add the construction: spunlace, air-laid, knitted, woven. Two cloths with the same fiber and different construction behave differently on absorbency and shedding.
6. Weight per area, with a tolerance
GSM plus a tolerance band — for example 120 GSM ±5%. Without the tolerance, a 108 GSM delivery technically complies with a 120 GSM specification. GSM does not predict shedding or capacity on its own; the absorbency note explains why.
7. Size and fold
Open size, folded size and fold type. A 30 × 30 cm wipe four-folded to 15 × 15 cm is a different product from the same cloth straight-folded. State both dimensions and the fold, or the converter will choose for you.
8. Pack presentation
Flat stack, interleaved, roll, sachet, canister. Include the count per pack, packs per carton and the bag construction — vacuum, double-bagged, or plain. Packaging is where most shelf-life and contamination complaints originate.
9. Sterility or bioburden claim
Sterile with a stated sterility assurance level and method (typically gamma), or non-sterile with a bioburden limit. “Clean” is not a claim. If the product is irradiated, state the dose range and whether the fold is validated for penetration.
10. Acceptance data per lot
Particle release, NVR, ionic extractables, absorbency, wet tensile — whichever of these the process depends on, with the method and the limit. Then state what happens on failure: hold, re-test, or reject. A specification without a failure clause is a wish.
The methods behind these numbers are in fiber release testing and NVR and extractables.
What this actually changes
A specification written this way can be quoted by three converters and compared line by line. It also survives an audit: the auditor asks why this cloth, and the answer is a document rather than a memory. The commercial effect is usually a narrower supplier list and fewer line trials, not a higher price.
Start with the surface you are cleaning and the data you can defend. If you want the ten fields applied to your process, send the surface and the soil and we will return a draft specification; samples follow once the fields are agreed.
Bottom line. Write the ten fields once and reuse the document. The first pallet gets cheaper, and the argument stops.
Frequently asked questions
How long should a wiper specification be?
One page is enough for most products. The value is in the fields, not the length: every line should be something a converter can build to and a buyer can reject against.
Do I need all ten fields for an industrial wipe?
No. For workshop use, fields 1, 2, 5, 6, 7 and 8 usually carry the decision. Fields 3, 4, 9 and 10 matter as soon as the wipe enters a controlled zone or a regulated product.
Who should write it — procurement or quality?
Quality owns the acceptance criteria and the data; procurement owns the commercial terms. The technical fields are best written by whoever runs the line trial, because they are the person who knows which failure actually costs money.
How often should the specification be reviewed?
At least once a year, and whenever the surface, solvent, class or supplier changes. A specification that survives a process change is usually one nobody reads.
Should the specification name a brand?
Name the construction and the data, not the logo. That keeps three converters able to quote and prevents one supplier from becoming the specification.
